Chief Manufacturing Indoor Furnishings FTR Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
SMALL FLAT PANEL ADJUSTABLE PITCH  
WALL MOUNT  
Model: FTR Series  
Specifications:  
Designed for installation on single wood studs or  
drywall (1/2" minimum thickness); either option  
provides ±1/2" lateral shift.  
Weight capacity:  
45 lbs (20 kg) for wood stud installation  
30 lbs (14 kg) for drywall installation  
Provides tilt range from 5° up to 15° down.  
BEFORE YOU BEGIN  
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using  
the instructions provided. Failure to read, thoroughly understand, and follow all instructions can result in serious  
personal injury, damage to equipment, or voiding of factory warranty.  
If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing  
at 1-800-582-6480 or 952-894-6280.  
Chief® is a trademark of Milestone AV Technologies, Inc. All rights reserved.  
Chief Manufacturing, a division of Milestone AV Technologies  
8804-000343 RevA  
©2008 Milestone AV Technologies  
1-800-582-6480 952-894-6280 Fax: 952-894-6918  
8401 Eagle Creek Parkway, Ste 700  
Savage, Minnesota 55378 USA  
06/08  
 
Installation Instructions  
Model: FTR Series  
TOOLS REQUIRED FOR INSTALLATION  
PARTS  
Drill  
After unpacking carton, inspect and verify contents (See  
Figure 1). If any listed parts are missing or damaged,  
contact Chief Customer Service at 1-800-582-6480.  
1/8" drill bit (wood stud installation)  
3/8" drill bit (drywall installation)  
Hammer (drywall installation)  
Phillips screwdriver, #2  
NOTE: Other tools may be required depending on your  
Table 1: Parts  
method of installation.  
Item  
10  
Description  
Qty  
2
PLATE, Wall  
20  
ANCHOR, Hollow Wall, #10-24  
WASHER, Flat, Standard Machine Screw, #10  
4
30  
4
40  
SCREW, Phillips Pan Head Sheet Metal,  
#10 x 2-1/2"  
2
(10)  
(20)  
(30)  
(40)  
Figure 1: Parts  
3
 
Model: FTR Series  
Installation Instructions  
INSTALL MOUNT TO DRYWALL  
INSTALLATION  
The FTR may be installed on either a single wood stud,  
or drywall (1/2" minimum thickness).  
WARNING: Drywall must be 1/2" minimum thickness.  
Failure to provide adequate structural strength for this  
unit can result in serious personal injury or damage to  
equipment!  
INSTALL MOUNT TO SINGLE WOOD STUD  
1. Determine approximate mounting location, keeping in  
mind the display size.  
1. Determine approximate mounting location, keeping in  
mind the display size.  
2. Use a stud sensor to locate applicable wood stud.  
Mark location with a pencil.  
2. Level plate (10) at desired height and, using plate (10)  
as a template, mark the location of the four anchor  
holes (one in each corner slot).  
3. Level plate (10) at desired height and, using plate (10)  
as a template, mark the location of upper and lower  
pilot holes. Ensure marks are in the center of wood  
stud.  
NOTE: Mount can provide ±1/2" of lateral shift by using  
WARNING: ELECTRICAL SHOCK HAZARD! Drilling  
into electrical wires or cables can cause DEATH or  
SERIOUS PERSONAL INJURY! ALWAYS make  
certain area behind mounting surfaces is free of  
electrical wires and cables before drilling or installing  
mount fasteners.  
mount holes on either side of vertical centerline.  
WARNING: ELECTRICAL SHOCK HAZARD! Drilling  
into electrical wires or cables can cause DEATH or  
SERIOUS PERSONAL INJURY! ALWAYS make  
certain area behind mounting surfaces is free of  
electrical wires and cables before drilling or installing  
mount fasteners.  
3. Drill anchor holes using a 3/8" drill bit. Ensure holes  
are straight and completely through drywall.  
4. Insert anchor (20) into anchor hole and seat with  
gentle tapping from hammer. Anchor barbs should be  
fully engaged in drywall (See Figure 3).  
4. Drill pilot holes using a 1/8" drill bit. Ensure pilot holes  
are straight.  
5. Using Phillips screwdriver, insert screw (40) through  
washer (30), plate (10), and drywall (not shown) and  
install into pilot holes (See Figure 2).  
Drywall  
(10)  
Anchor barb  
Pilot  
Holes  
(2 places)  
(40)  
(2 places)  
Not collapsed  
Figure 3: Drywall Anchor  
Collapsed  
5. Using Phillips screwdriver, tighten anchor screw until  
anchor has fully collapsed against back side of  
drywall.  
Wood  
Stud  
NOTE: Anchor screw will feel tight until anchor begins to  
collapse. Screw will then turn easier for many  
turns. Screw will feel tight when anchor has fully  
collapsed.  
(30)  
(2 places)  
Figure 2: Installation to Single Wood Stud  
6. Repeat steps 4. and 5. for remaining anchors.  
6. Repeat for remaining screw (40).  
7. Tighten both screws (40) securely.  
7. Remove and retain anchor screws from anchors (20).  
NOTE: Anchors (20) may come with small washers which  
may be left on the screw or discarded. These  
small washers do NOT replace washers (30).  
8. Using Phillips screwdriver, insert anchor screws  
through washers (30) and plate (10) and install into  
4
 
Installation Instructions  
Model: FTR Series  
collapsed anchors (20). Tighten until secure (See  
Figure 4).  
Button location for  
100mm x 100mm  
pattern (4 places)  
(20)  
(4 places)  
(30)  
(4 places)  
Button location for  
75mm x 75mm  
pattern (4 places)  
NOTE: Display not shown for clarity.  
Anchor  
Screw  
(4 places)  
(10)  
Figure 6: Install Display to Plate  
3. Close latching flag by rotating flag counterclockwise  
on plate (10) (See Figure 7).  
Figure 4: Installation to Drywall  
NOTE: An optional padlock may be used to secure  
latching flag.  
INSTALL DISPLAY TO MOUNT  
NOTE: Proper interface must be attached to display. See  
instructions that come with interface assembly.  
1. Open latching flag by rotating flag clockwise on plate  
(10) (See Figure 5).  
Latching  
Flag  
(10)  
Latching  
Flag  
NOTE: Display not shown for clarity.  
Figure 7: Close Latching Flag  
4. Connect cables to display as required.  
(10)  
REMOVE DISPLAY FROM MOUNT  
Figure 5: Open Latching Flag  
1. Disconnect all cables from display.  
2. Lift and maneuver display such that all buttons fit into  
button openings on plate (10). Lower display firmly  
into place. Ensure each button has fully seated in its  
button opening (See Figure 6).  
2. Open latching flag by rotating flag clockwise on plate  
(10) (See Figure 5).  
3. Lift and maneuver display mounting buttons out of  
button openings.  
NOTE: Mounting buttons are shown in the 100mm x  
100mm pattern. Plate (10) will also  
accommodate a 75mm x 75mm pattern.  
5
 
Model: FTR Series  
Installation Instructions  
ADJUST TILT  
1. Loosen adjusting screws on each side of display (See  
Figure 8).  
2. Adjust tilt as desired.  
3. Retighten adjusting screws.  
Adjusting  
Screw  
(other side  
similar)  
5° Tilt Up  
15° Tilt Down  
Figure 8: Tilt Adjustment  
6
 
Installation Instructions  
Model: FTR Series  
7
 
 

Belkin Computer Drive P74080 User Manual
Black Box Surge Protector SP250A User Manual
Black Decker Carpet Cleaner FSM1630 XE User Manual
Blomberg Printer TKF 7230 User Manual
Bostitch Cordless Saw BTE360K User Manual
Bostitch Nail Gun N88RH User Manual
Bushnell Binoculars 11 1026 User Manual
Campbell Hausfeld Nail Gun JB006750 User Manual
Chicago Electric Welding System 94009 User Manual
Chief Manufacturing Indoor Furnishings JHS Series User Manual